57mm Series 2 Phase Close-loop Stepper Motor

42mm Series 2 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MR Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) YK242EC51E1 1.8 79 0.5 1.85 1.0 1.9 77 0.53 YK242EC67E1 1.8 95 0.77 2.3 1.45 2.8 115 0.6 Suitable drive model: SSD2205M Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)      YK242EC51E1 8 Flat 0.5*15 21 YK242EC67E1 8 Flat 0.5*15 21 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Motor standard cable: 1.5m (optional 2m/3m) Encoder standard cable: 1.5m (optional 2m/3m) Motor connection

60mm Series 2 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MR Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) YK260EC65E1 1.8 87 2.0 5.0 0.3 1.2 490 1.0 YK260EC86E1 1.8 108 3.0 5.0 0.4 2.0 690 1.3 YK260EC65E1-KZ01 1.8 87 2.0 5.0 0.3 1.2 490 1.0            YK260EC86E1-KZ01              1.8 108 3.0 5.0 0.4 2.0 690 1.3 Suitable drive model: SSD2205M Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK260EC65E1 8 Flat 0.5*20 24 YK260EC86E1 8 Flat 0.5*20 24 YK260EC65E1-KZ01 8 Flat 0.5*25 30 YK260EC86E1-KZ01 8 Flat 0.5*25 30 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Motor standard cable: 1.5m (optional 2m/3m) Encoder standard cable: 1.5m (optional 2m/3m) Motor connection

86mm Series 2 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK286EC80A1 1.8 97 4.2 6.0 0.34 2.7 1800 2.4 4 YK286EC118A1 1.8 140 8.2 6.0 0.52 4.7 3200 4.0 4 YK286EC156A1 1.8 174 12.0 6.0 0.7 9.2 5400 5.4 4 Suitable drive model: SSD2608H Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK286EC80A1 14 Key 5*5*25 40 YK286EC118A1 14 Key 5*5*25 40 YK286EC156A1 14 Key 5*5*25 40 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Motor standard cable: 1.5m (optional 2m/3m) Encoder standard cable: 1.5m (optional 2m/3m) Motor connection

110mm Series 3 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK385EC127A1 1.2 156 12 4.2 1.2 13 9320 6.5 3 YK385EC156A1 1.2 238 20 4.2 1.88 18 12510 10.4 3 Suitable drive model: MS-L3 Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK3110EC140C1 19 Key 6*6*30 39 YK3110EC220C1 19 Key 6*6*30 39 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Encoder standard cable: 2m (optional 8m/10m) No more motor cable needed Motor connection

Stepper drive auto-setup measures motor parameters and configures motor current control and anti-resonance gain settings. The high voltage drive uses ac input 90 to 240 Vac and output current is selectable from 0.6 to 2.5 A/phase (peak of sine).

MCC800P is a PCI-based motion control card for controlling stepper motors and servo systems. Motion planning through ARM and FPGA, pulse commands can be output, which can control 1-8 axes servo or stepper motor at the same time. The maximum frequency of each axis is 4MHz, and the 8-axis encoder input signal can be detected. It supports linear and circular interpolation, supports trapezoidal and S-shaped acceleration and deceleration point-to-point motion control, and supports speed/positoion change during motion. The position command can be output by single pulse (pulse + direction) or double pulse (CW + CCW pulse); it can be a differential output circuit or a single-ended output circuit.
MCC800P matched terminal board has multiple general I/Os, supports high-speed position latching and position comparison output. External bus I/O expansion greatly satisfies customers' various control requirements for I/O.

This product is equipped with a dynamic link library under Windows XP/Win7, which is convenient for customers to write their own application software. At the same time, it provides motion debugging software, which can demonstrate the function of this card, it also can be used to tests the operation of motion control cards, motors and drives and motion platforms.

Typical Application:

Widely used in PCB industry, semiconductor packaging industry, electronic processing industry, sheet metal processing industry, testing industry, such as: PCB drilling machine, PCB punching machine, solid crystal machine, ultrasonic wire bonding machine.

42mm Series 2 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MR Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) YK242EC51E1 1.8 79 0.5 1.85 1.0 1.9 77 0.53 YK242EC67E1 1.8 95 0.77 2.3 1.45 2.8 115 0.6 Suitable drive model: SSD2205M Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)      YK242EC51E1 8 Flat 0.5*15 21 YK242EC67E1 8 Flat 0.5*15 21 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Motor standard cable: 1.5m (optional 2m/3m) Encoder standard cable: 1.5m (optional 2m/3m) Motor connection

The AC stepper drive is powered from 24 to 50V and is intended for use with step motors designed to handle a high bus voltage of 340VDC.