banner

SSD2608H 100% True Capacity Yako 2 Phase Closed-Loop Stepper Drive

That closed stepper system can be used to upgrade open loop stepper systems or replace some servo systems, especially in many small to median speed applications such as CNC routers, CNC mills, CNC laser cutters, CNC plasmas, lab automation instruments, plotters, medical equipment, electronic equipment, small packaging machines, etc.
  • Brand:

    Yako
  • Item no.:

    SSD2608H
  • Payment:

    100% T/T payment before delivery
  • Product origin:

    Made in China
  • Product weight:

    0.3kg
  • Lead Time:

    Normally 7 workdays
  • Product Detail

SSD2608H 100% True Capacity Yako 2 Phase Close-Loop Stepper Drive


Our SSD2608H is a closed loop stepper drive, It can close the position loop between the motor and drive and therefore eliminate the loss of step problem in an open loop system. The SSD2608H implements advanced control algorithm based on YAKO Automation tens of years’ experience in stepper and servo controls. It is ideal for upgrading open loop stepper systems, or replacing servo systems in some low to middle speed applications.


Features:


  • 32-bit motor control dedicated DSP chip
  • Voltage range: AC20-80V/DC30-110V, 16 microstep setting
  • With overcurrent, overvoltage, undervoltage, tracking error tolerance and other protection
  • Advanced power angle closed loop control technology
  • The current is intelligently adjusted according to the load
  • The highest pulse response frequency is 200KHz
  • Low torque attenuation, speed up to 3000rpm
  • Built-in in position and alarm output for easy monitoring and control
  • Optocoupler isolated differential signal input
  • Small size, volume 151.2*94.3*54 (mm³), weight 0.3kg
  • Suitable for 60/86mm(NEMA24/34) 2 phase close-loop stepper motors


Application: 

Application: Mainly used in engraving machines, special industrial sewing machines, wire stripping machines, marking machines, cutting machines, laser phototypesetting, plotters, CNC machine tools and other automation equipment and instruments.
closed-loop stepper servo drive


Dimensions


SSD2608H Microstep Setting


SSD2608H Motor Selection


Terminal Introduction


Notice:

1. Please ensure that the motor and encoder are wired correctly, otherwise the motor will be out of
 tolerance after receiving the pulse.
2. The input control signal level is 5V. The current limiting resistor needs to be connected when>5V.
3. When installing the motor, it is strictly forbidden to strike the back cover of the motor to avoid damage
 to the encoder.

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Related products
2-phase closed loop stepper drive
SSD2505M High performance Yako 2 Phase Close-Loop Stepper Drive
Stepper drive auto-setup measures motor parameters and configures motor current control and anti-resonance gain settings. The high voltage drive uses ac input 90 to 240 Vac and output current is selectable from 0.6 to 2.5 A/phase (peak of sine).
2-phase hybrid stepper motor Drive
SSD2505M-PLUS 2 Phase Closed Loop Stepper Motor Drive
This stepper servo motor is designed based on the Cz optimized magnetic circuit and adopts stator and rotator materials of high magnetic density, featuring high energy efficiency.
2-phase closed loop stepper drive
SSD2205M High performance Yako 2 Phase Close-Loop Stepper Drive
Stepper drive auto-setup measures motor parameters and configures motor current control and anti-resonance gain settings.
Open-Loop Stepper Drive
YKD2204PA 2 Phase Open-Loop Stepper Drive DC18~36V
YKD2204PA open-loop stepper drive feature for 32-bit DSP control, low noise and superior vibration performance, with over voltage, under voltage etc. fault protection.
CAN Bus Stepper Drive
YKD2405PC Yako High Performance CAN Bus Type Stepper Motor Drive
CAN bus type stepping motor driver series, simple instructions and intelligent control. The system consists of a gateway and multiple drives connected in series via CAN bus.
MCC-32E  EtherCAT control card
MCC-32E EtherCAT control card
   MCC-32E is an EtherCAT control card that controls the motion of 32-axis motors with a bus refresh cycle of 1ms. It comes with 1 auxiliary encoder input, 8 digital inputs and 8 digital outputs (including 4 high speed PWM outputs). With CAN, RS485 bus, expandable 512/256/128 input\output\AD\DA, support Basic multi-tasking programming, 6 tasks, 10 files, so that program developers can easily write programs. And in linear, circular and spiral interpolation, space arc, support speed preview, electronic gear, electronic cam, motion superposition, virtual main axis, hardware latch, comparison output and other functions, it is comparable to the pulse type controller. In addition, it provides 4 high-speed color-coded inputs, 1us measurement accuracy, and supports continuous latching. This control card adapted to various types of robots (Delta, SCARA) multi-axis group, multi-manipulator coordinated motion.
Open-Loop Stepper Drive
YKE2608MH 2 Phase Open-Loop Stepper Drive AC18~80V
YKE2608MH open-loop stepper drive feature for 32-bit DSP control, low noise and superior vibration performance, with over voltage, under voltage etc. fault protection.
Open-Loop Stepper Drive
YKD2305M 2 Phase Open-Loop Stepper Drive
YKD2305M is high performance digital step driver based on YAKO’s new 32-bit DSP technology. It’s designed for various models of two phase 42~60mm (NEMA 17~24) hybrid stepper motors which current are below 3A.
News letter
Join our mailing list, you will get new product release and event information as soon as possible later
Leave A Message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

skype

whatsapp